Pistons & Rods

piston2The China Girl 66cc/80cc 2 cycle engine has basically 3 engine geometrics and could be broken into separate classes ie: PK80 – GT5 – Half Breed.

Here is a way to measure and know if you have the 110mm or 115mm Con Ron length without taking the motor apart. Stick a caliper or screw driver along the side of the rod and measure. If you measure around 80mm then you have the 110mm Con Rod, if you measure around 85mm , then you have the 115mm con rod.

Another way to tell: If you have a 40mm stroke, the piston will likely come to the top of the barrel on TDC (or close to), if you have a 38mm the piston is likely to sit a little low in the barrel at TDC.

This is important to know since the top ends are designed around the con rod length. Be aware that there are several different case bottoms as well as upper cylinders. Matching the correct combination is important on a good quality built engine.

Type A = 15/16″ Bottom of piston to center of connecting rod. Used on 40mm rods. Also on specialized ZAE 50 rods 38mm stroke – If you have this rod and crank, double check.

Type B = 1 1/16″ Bottom of piston to center of connecting rod. Used on 38mm rods.

 ——————————————-


Z-L & ZL Rod = 40mm / Type A Piston – PK Type (Caged and Non-Caged) *

ZL E80 Rod = 40mm / Type A Piston – PK Type *

ZL40MM Rod = 40mm / Type A or B depends on cylinder – Overcut journal = junk.

Zeda 80 Rod = 40mm / Type A or B depends on cylinder – Overcut journal = junk.

FM80 Rod = 38mm / Type B Piston – GT5 Type *

F80 Rod = 40mm / Type A Piston * Use #2 B w/ 41mm tall cylinder – GT5 Type

ZAE 50 Rod = 38mm / Type A Specialized crank setup.= 38mm / Type A Piston – PK Type *

ZAF80 Rod = 38mm / Type B Piston – GT5 Type *

No Mark Rod = 40mm / Type A Piston – PK Type (Caged) *

SX-OP = 111.47 mm (Overall) ?????

ZAF 60 Rod =

ZAE 80 = 40mm / Type B Piston – GT5 Type * Double check piston!

ZMN = 38mm / Type A Piston – Halfbreed type * Always double check

JSF50 =

CY Rod = 38mm / Type A Piston – Halfbreed Type

ZAF 50, ZAF 60, and ZAF 80. The higher the number, the longer, and therefore heavier. You can run a pk piston in a gt5 as long as the con rod has z-l on it or zaf 50 not the zaf 60 though and yes the jugs are different the biggest visual difference is the gt5 usually has a tapered transfer port window.

The A80 engine uses a long ZL rod that is counter sunk at the bearings and is not heat treated. This engine uses a type B piston

—————————————————
Grubee Skyhawk GT5SR Super Rat Angle Fire 66cc/80cc
Front mount diameter (40mml/1.57in)
Rear mount diameter (32mm/1.26in)
Integrated CDI Ignition Coil
Timing key way cut at approx. 3:00 TDC
17mm Crank – Larger key way @ magnet
6203 Crank Bearings
Z-L 115mm / 40mm Stroke
Type A Piston – Top end con rod needle bearing – 10 x 14 x 13

GT5A and Super Rat 66cc use the same piston.

66/80cc Piston #2
Only compatible with the Flying Horse Bike Engine Kit*

Piston Measurements:
Height: 49mm
Width: 47mm
Skirt Width: 19mm
Skirt Height: 5mm
Piston Pin Port: 5mm
Height from Skirt to Piston Pin: 5mm

—————————————————————-

66/80cc Piston #4
Compatible with most Grubee Skyhawk Bicycle Engine Kits*

Piston Measurements:
Height: 50mm
Width: 47mm
Skirt Width: 23mm
Skirt Height: 10mm
Piston Pin Port: 10mm
Height from Skirt to Piston Pin: 5mm

—————————————————————-

66/80cc #5
This piston fits most 66/80cc Flying Horse, Mega Motors, and RAW* engine kits.

Piston Measurements:
Height: 50mm
Width: 47mm
Skirt Width: 19mm
Skirt Height: 11mm
Piston Pin Port: 5mm
Height from Skirt to Piston Pin: 7mm

Bearing Reference:

NTN 6202LLUC3/5C

Malossi racing top end con rod needle bearing – 10 x 14 x 13